This Is A Custom Widget

This Sliding Bar can be switched on or off in theme options, and can take any widget you throw at it or even fill it with your custom HTML Code. Its perfect for grabbing the attention of your viewers. Choose between 1, 2, 3 or 4 columns, set the background color, widget divider color, activate transparency, a top border or fully disable it on desktop and mobile.

This Is A Custom Widget

This Sliding Bar can be switched on or off in theme options, and can take any widget you throw at it or even fill it with your custom HTML Code. Its perfect for grabbing the attention of your viewers. Choose between 1, 2, 3 or 4 columns, set the background color, widget divider color, activate transparency, a top border or fully disable it on desktop and mobile.

FAQ Page

/FAQ Page

Absolutely not! Dakota Shine is BETTER than a clear-coat and is designed to penetrate/absorb into the surface and restore the faded & oxidized pigments back to their original color.  Dakota Shine will not burn, flake or scratch off (unless it has been applied too thick).

A simple test is to put a piece of scotch tape to the surface that you are going to apply Dakota Shine, apply Dakota Shine and remove tape.  If applied correctly, you should not be able to feel where the tape was.

The restored color and luster should lat as long a the original surfaces did – in comparable conditions.

Dakota Shine can be used on any painted surface, decals, plastics and some rubber components, as long as there is pigment still remaining within the surface/material.

Nothing, except plexi-glass.  Plexi-glass must be masked off because lacquer thinner can damage the surface.  Dakota Shine can be applied up to all galls surfaces.  Over-spray can be removed with lacquer thinner and a cotton cloth.  Dakota shine will not harm chrome cylinders, lights or gauges; no cleanup is necessary on these surfaces.

Yes. The process is designed to restore the original color, but the surface will begin fading and oxidizing naturally due to the sun. So, you could apply Dakota Shine as part of a yearly maintenance program to keep your surfaces looking like new, or just apply once.  Remember, that there must be good pigments remaining under the faded and oxidized pigments to complete our process, if the surface is completely oxidized through, then you must repaint.

No. Dakota Shine needs to be applied in a controlled enviroment.  A wash bay, an isolated service bay or a paint booth could be utilized to apply Dakota Shine.  It could be Outside on a warm (65° – 85°F), calm day on an asphalt/concrete lot, but it is not recommended.

We would recommend that you wear a mask when applying Dakota Shine, especially if you are applying large amounts of Dakota Shine on a consistent basis.

Yes.  If Dakota Shine is applied like a paint (i.e. as a coating), it may run and will not provide the proper results.  So apply Dakota Shine a one thin and even spray.

Lacquer Thinner.  Use a basic lacquer thinner to wash out the paint gun, and spray a small amount of lacquer thinner through the nozzle to remove any excess Dakota Shine in the ports.

No. Dakota Shine is a ready-to-use product, no mixing required.

No. Any remaining Dakota Shine can be poured back into the container and reused at a later date.

Yes.  After you Prep the surface, you can spot paint the scratches or damaged spots using OEM paint.  Dakota Shine must be applied before the paint dries.

No.  None of the ingredients in Dakota Shine will affect a paint booth.

Absolutely not!  All you need is some common-sense and the willingness to use a new and exciting product.  Application is very simple.

If the cap is kept tightly closed, there is no shelf life for Dakota Shine.

If applied correctly, Dakota Sine will cover approximately 400 square feet of surface area, which is equivalent to 4 or more medium sized pickups or two to 3 medium sized tractors.

Yes.  Dakota Shine carries a “2” on the NFPA flammability rating, but will burn like lamp oil.  So take precautions when uing the product.

It is recommended.  If applying a large amount of Dakota Shine on a consistent basis, a respirator is necessary.  If applying a small amount of Dakota Shine, use your best judgement.

No, the Dakota Shine product is considered hazardous due to the chemical make-up and the aerosol can of Dakota spray cannot be shipped by air-freight.

Dakota Shine Averages 10% or higher within the auction industry.  When compared to purchasing direct from DAI, the margin is 30% to sales for end users.

None.  Dakota Shine will revitalize the appearance of the machine decals to a like-new appearance as it does to the machine surface.

No.  Do not dilute Dakota Shine with any liquid.

For best results, it is recommended that the temperature of the surface of the equipment be 70° F or above at the time of the application.